News
1. Firstly, confirm the material of the drill bit, select the appropriate grinding wheel according to the material of the drill bit, and install it on..
View More
After the power is turned on, turn on the power controller, set the tapping speed, press and hold the forward rotation, the servo motor converts the voltage signal into torque and speed output for tapping, and press and hold the reverse button when tapping to the bottom to withdraw. The work wire ha..
View More
1. The operator can only operate after passing the examination and obtaining the operation certificate. The operator should be familiar with the performance and structure of the machine, 2. Before work, check according to the requirements of the equipment spot check card, and inject oil according to..
View More
請使用者使用鑽頭研磨機前後以空壓槍，清潔所有機台灰層鐵屑，尤其是研磨接觸孔之清潔，以確保機台使用壽命。更換砂輪正確方法，鬆開固定螺絲，打開砂輪保護蓋，取下砂輪固定螺絲及扇葉片，取出砂輪，將砂輪及軸心接觸麵擦拭幹淨，砂輪新品裝入軸心，扇葉片及固定螺絲裝回，再將固定螺絲鎖緊，蓋回砂輪保護蓋，鎖上外殼固定..
View More
電動攻絲機是一種可對各種小型及大型鋼件的粗牙、細牙、非標牙距的正轉及反轉緊固連接螺紋、傳動連接螺紋及管螺紋進行內螺紋攻絲機床，該類機床屬柔性攻絲範疇，顯著特點是可折臂操作，適應M42以下螺紋攻絲要求。製動方式齒輪車身重量50kg目錄1簡介2特點3技術參數4操作方法5組成結構簡介編輯electrict..
View More
1.開機前檢查電機的電壓和頻率是否和電源一致。2.機床電源插頭、插座上的各觸角應緊固可靠，無鬆動或接觸不良現象。3.當發生故障或有不正常聲音應立即拔掉插頭，然後進行檢查修理。4.不要讓機床在無人情況下運轉，一定要在開機後，停止運轉才能離開。外界切斷電源，應按紅色鈕，否則機床會無人情況下來運轉。5.不..
View More
夾頭組之組裝夾具組裝步驟1.先確定鑽頭材質，並選用合適之砂輪使用。※CBN砂輪適用HSS(高速鋼)材質、SD砂輪適用鎢鋼材質。2.將左側調整台調整刻度歸零：順時針旋轉到底,逆時針調到“0”的位置。A.選擇適用筒夾放入夾頭座。(以45°將筒夾嵌入夾頭座)B.放入順序：筒夾及夾頭座與固定夾頭螺帽鏈接，再..
View More
1.1 The machine has passed the qualification inspection and strict packaging treatment before delivery, but in consideration of the transportation process and other factors, special attention should be paid before installation. If there is any abnormality, please inform the product dealer or the rel..
View More
scan
聯係我們
138-2575-1784
